bumper4fiat124spider

Your e-mail:
Message:
send
send
Formularz został wysłany - dziękujemy.
Proszę wypełnić wszystkie wymagane pola!

Lights

 

The lights have to be connected with original cables, depending on the existing plug version, it may be necessary to cut the cables to the existing lamps and to install the new supplied plugs, the poles of the mew lamps are crearly marked. The lights are attached to the back of the front panel with super strong neodymium magnets, so that no work is necessary there. The new, 3 mm thick ABS plastic base can be painted by the buyer in the car color or any other.

 

bumper4fiat124spider_lightset

I always loved my 77’ Fiat 124 Spider, except it's ugly bumpers. In 1974 the US regulations forced all manufacturers to adopt to so called 5MPH rule. This rule says that during the crash test with the speed of 5MPH no damage should reveal. This rule was forced by the insurers trying to avoid policy payments from 90% low speed traffic jam accidents, caused by automatic transmission careless braking. FIAT designed and adopted the new heavy (ca. 30 kg each) bumper with shock-absorbers, making the car look and drive much worse than the original one. As most of the Spiders were sold in the US, FIAT sold the new bumper on all markets. The 5PM rule bumpers is not only the matter of aesthetics, by far the worst part of those heavy  battering rams is what they do to handling. It’s much worse than an extra passenger on board, as this extra weight is located on car’s very ends. All that weight hanging as the pendulum there is disastrous, making a sweet-handling machine into a nervous slug. Here is our cure for that pain.

ORDER

To order your bumper4fiat124spider select your option from a white scroll down box below and tap the yellow "Buy Now" button, then follow PayPall instructions. The full package consist of rear and front bumper with two plastic front license plate clamps and set of lights installed(as pictures below) on newly designed, 3mm plastic base and . New 7,5mm lights, looks straight forward and are visible from the car side, they are attached to the back of the front panel with 4 super strong neodymium magnets. The E11 certified lamps are equipped with double filament conventional 21/5W bulbs for turn & park, for Europe only the 21W turn filament will be used. Older light options from the images other than below are not longer available. 
The front bumper has two pairs of fixing holes to choose from, for slicker look or more protection.
The handling time for this items is 7 days.
Worldwide air shipment is included in purchase from this website.

Front

 

The front bumper main screws "C" are accessible through wheel arches, turn the wheels for easy access. There are two additional screws"D" holding the metal clamp that press the rubber ring over the damper tube, accessible through the rectangular openings where the lights will be placed. These two screws just need to be loosened, they don't have to be removed, pull out the old bumper, insert the new one, screw the screws back in. The new front bumper has two pairs of mounting holes to choose from, for a smoother look or more protection. Don't forget to grease the screws when reseting them.

 

bumper4fiat124spider_front_installation
bumper4fiat124spider_back_installation

The bumper conversion is simple and does not require any special tools or skills, the work should not take more than 2-3 hours. There is absolutely no cutting, drilling, or painting of any part required, the whole process is trace free reversible.

 

Rear

 

The two rear fastening screws "A" are located in the trunk.
Before starting the installation, it is recommended to run the fuel tank almost empty to make it light. It is necessary to unscrew it and lift it up slightly in order to be able to remove the rear bumper left fixing screw . The tank does not have to be completely separated and dismantled, just remove the 4 fastening screws
"B"and lift the tank a bit from behind, it is much easier if it is light. Remove both screws, pull out the old bumper, insert the new one, screw in the screws again, fasten the tank again.

Fiat 124 Spider bumper conversion manual

bumper4fiat124spider_conversion
bumper4fiat124spider
bumper4fiat124spider_bumperless
bumper4fiat124spider_5MPH
bumper4fiat124spider_1966

Fiat 124 Spider bumper conversion

First you can do is remove the bumpers completely, the car looks and runs better, but something is missing visually and there is entirely no protection.

You can downgrade it to before 1975 look, but the installation of original very expensive bumpers and turn indicators requires front panel cutting, paint job and is irreversible . Some other options cost a lot of money and effort but the result is not always perfect.

Our solution is not pretending anything. Completely new designed bumpers and front turn & park lights. Within ca. 2 hours using simple wrenches, original screws and mounting brackets you can fit your Spider with new bumpers. Beautifully bended, welded and polished, stainless steel pipes will fit all post 1974 Spiders.

Many loves the original Fiat Spider, Pininfarina design presented in 1966, but “You Can’t Always Get What You Want”. It’s difficult to find a good rust free car in original form, from before 1975.

Many  bought the post 1975 Spiders with the ugly and heavy rubber/pipe 5 mph bumpers really disturbing the clean Pininfarina line. 

Restore the beauty of clean Pininfarina line with bumper4fiat124spider

  1. en
  2. de

bumper4fiat124spider

 

Many loves the original Fiat Spider, Pininfarina design presented in 1966, but “You Can’t Always Get What You Want”. It’s difficult to find a rust free car in original form, from before 1975.

ot of us bought the post 1975 Spiders with the ugly and heavy rubber/pipe bumpers, really disturbing the clean Pininfarina line.

GALERY

OPIONS